View metadata View metadata

Technical Data
Solvalitt
Product description
Solvalitt is a heat resisting paint based on silicone acrylic binder.

Recommended use
To be used as a topcoat on items exposed to high temperatures (up to 600ºC) in combination with Zinc Silicate coatings, maximum 400ºC.
Film thickness and spreading rate
Aluminium
Minimum
Maximum
Typical
Film thickness, dry (µm)
20
30
20
Film thickness, wet (µm)
55
80
55
Theoretical spreading rate (m²/l)
19
12.7
19
Colours
Minimum
Maximum
Typical
Film thickness, dry (µm)
20
30
20
Film thickness, wet (µm)
50
70
50
Theoretical spreading rate (m²/l)
21
14
21

Physical properties
ColourAluminium, Black, Green, Grey, White
Solids (vol %)*40 ± 2 Aluminium
43 ± 2 Colours
Flash point26°C (Setaflash)
VOCAluminium
4.43 lbs/gal (530 gms/ltr) USA-EPA Method 24
500 gms/ltr UK-PG6/23(97). Appendix 3
Colours
4.34 lbs/gal (520 gms/ltr) USA-EPA Method 24
490 gms/ltr UK-PG6/23(97). Appendix 3
GlossAluminium sheen/Flat
FlexibilityGood
*Measured according to ISO 3233:1998 (E)
Other colours (limited range) can be supplied on request and may be subject to maximum temperature limitations below 600 °C depending on specific pigments heat resistance.
Please consult with Jotun local office for detail.


Surface preparation

All surfaces should be clean, dry and free from contamination. The surface should be assessed and treated in accordance with ISO 8504.

Bare steel
Cleanliness: Blast cleaning to Sa 2½ (ISO 8501-1:2007). Roughness: using abrasives suitable to achieve grade Fine to Medium G (30-85 µm, Ry5) (ISO 8503-2)

Coated surfaces
Cured and clean zinc silicate primer.

Other surfaces
The coating may be used on other substrates. Please contact your local Jotun office for more information.


Condition during application
The temperature of the substrate should be minimum 3ºC above the dew point of the air, temperature and relative humidity measured in the vicinity of the substrate. Good ventilation is usually required in confined areas to ensure correct drying.

Application methods
SprayUse airless spray or conventional spray
BrushRecommended for stripe coating and small areas, care must be taken to achieve the specified dry film thickness.
RollerMay be used for small areas but not recommended for first primer coat, however when using roller application care must be taken to apply sufficient material in order to achieve the specified dry film thickness.

Application data
Mixing ratio (volume)Single pack.
Thinner/CleanerJotun Thinner No. 7
Guiding data airless spray
Pressure at nozzle15 MPa (150 kp/cm², 2100 psi).
Nozzle tip0.38-0.48 mm (0.015-0.021")
Spray angle40-60°
FilterCheck to ensure that filters are clean.


Drying time
Drying times are generally related to air circulation, temperature, film thickness and number of coats, and will be affected correspondingly. The figures given in the table are typical with:
* Good ventilation (Outdoor exposure or free circulation of air)
* Typical film thickness
* One coat on top of inert substrate

Substrate temperature5°C10°C23°C40°C
Surface dry 60 min45 min30 min15 min
Through dry 4 h3 h2 h1,5 h
Dry to recoat, minimum 8 h5 h4 h3 h
Dry to recoat, maximum 1
  1. The surface should be dry and free from any contamination prior to application of the subsequent coat.

The given data must be considered as guidelines only. The actual drying time/times before recoating may be shorter or longer, depending on film thickness, ventilation, humidity, underlying paint system, requirement for early handling and mechanical strength etc. A complete system can be described on a system sheet, where all parameters and special conditions could be included.

Typical paint system

Resist 78, Resist 86 or Resist GTI 1 x 75 µm (Dry Film Thickness)
Solvalitt 1 - 2 x 20 µm (Dry Film Thickness)
or
Solvalitt 2 - 3 x 20 µm (Dry Film Thickness)

Other systems may be specified, depending on area of use


Storage
Storage condition are to keep the containers in a dry, cool, well ventilated space and away from source of heat and ignition. Containers must be kept tightly closed. The container must be protected from freezing.
SHELF LIFE: 2 years at 23°C, subject to re-inspection thereafter. Storage at elevated temperatures will reduce product shelf life significantly.


Handling
Handle with care. Stir well before use.

Packing size
5 litre container

Health and safety
Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do not breathe or inhale mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.

For detailed information on the health and safety hazards and precautions for use of this product, we refer to the Material Safety Data Sheet.

DISCLAIMER
The information in this data sheet is given to the best of our knowledge based on laboratory testing and practical experience. However, as the product can be used under conditions beyond our control, we can only guarantee the quality of the product itself. We also reserve the right to change the given data without notice. Minor product variations may be implemented in order to comply with local requirements.
If there is any inconsistency in the text the English (UK) version will prevail.

Jotun is a World Wide company with factories, sales offices and stocks in more than 50 countries. For your nearest local Jotun address please contact the nearest regional office or visit our website at www.jotun.com
ISSUED 26 NOVEMBER 2010 BY JOTUN
THIS DATA SHEET SUPERSEDES THOSE PREVIOUSLY ISSUED



PDF Version :


TDS - Solvalitt - English (uk) - Issued.26.11.2010.pdf - TDS - Solvalitt - English (uk) - Issued.26.11.2010.pdf

Additional PDF versions:

No documents found